Murray 225114X92E2 Lawn Mower Manual

The Murray 225114X92E2 is a 22-inch, 190cc Briggs & Stratton-powered push lawn mower with a 5.5 HP engine, 2-in-1 side discharge/mulching capability, 3-in-1 adjustable cutting heights (1.5-3.75 inches), single-lever height adjustment, durable steel deck, easy-start system, and rear bagger. Below are key sections for safety, features, assembly, operation, maintenance, and troubleshooting.

1. Features at a Glance 2. Assembly Instructions 3. First-Time Setup 4. Specifications 5. Controls and Operation 6. Cutting & Height Adjustment 7. Maintenance Schedule 8. Storage & Winterization 9. Safety Information 10. Warranty & Support 11. Troubleshooting

Features at a Glance

Key components: 190cc Briggs & Stratton engine, 22-inch steel cutting deck, rear grass bag, height adjustment lever, recoil starter, fuel tank, oil dipstick, air filter, and wheels.

FeatureDescription
Engine190cc Briggs & Stratton, 5.5 HP, 4-cycle
Cutting Width22 inches
Cutting Heights3-in-1 adjustable (1.5", 2.5", 3.75")
Deck MaterialDurable steel
Discharge OptionsSide discharge, mulching, bagging (rear bag)
Starting SystemRecoil pull-start
Fuel Tank Capacity1.0 quart (0.95 liters)
Wheels8-inch rear, 7-inch front
WeightApprox. 65 lbs (29.5 kg)
Warranty2-year limited

Assembly Instructions

Unpack and inspect all parts. Assemble on a flat, clear surface.

  1. Attach handle: Align lower handle with deck brackets, secure with provided bolts and washers.
  2. Install upper handle: Connect to lower handle, tighten knobs or bolts.
  3. Attach grass bag: Hook bag frame onto rear deck brackets; ensure bag is secure.
  4. Install wheels: Slide axles through deck holes, secure with retaining clips or nuts.
  5. Add engine oil: Use SAE 30 detergent oil (approx. 20 oz); check dipstick.
  6. Add fuel: Use unleaded gasoline (87 octane minimum); fill tank to indicated level.

WARNING! Wear gloves during assembly. Ensure all fasteners are tight before operation.

First-Time Setup

Complete assembly, then perform pre-operation checks.

  1. Check oil level: Ensure oil is at FULL mark on dipstick.
  2. Check fuel: Fill with fresh unleaded gasoline (no ethanol preferred).
  3. Adjust cutting height: Set lever to desired position (middle recommended for first use).
  4. Inspect blade: Ensure it is secure and undamaged.
  5. Test start: Pull recoil starter slowly until resistance is felt, then pull briskly.

CAUTION! Never add fuel while engine is hot or running. Operate outdoors only.

Specifications

Controls and Operation

Primary controls: Recoil starter, throttle control, blade control bail, height adjustment lever.

Starting Procedure:

  1. Move throttle to FAST position.
  2. Prime engine (if equipped) by pressing primer bulb 3 times.
  3. Pull recoil starter briskly.
  4. Once started, squeeze blade control bail against handle to engage blade.

Stopping: Release blade control bail, move throttle to STOP, wait for blade to stop.

Height Adjustment: Move lever to one of three positions; ensure all wheels are at same height.

Cutting & Height Adjustment

For best results, mow when grass is dry. Overlap passes by 2-3 inches.

  1. Select discharge mode: Install side discharge chute for throwing clippings; remove chute for mulching.
  2. Adjust height: Use single lever to raise/lower deck.
  3. Mowing pattern: Alternate direction each time to prevent rutting.
  4. Bagging: Attach rear bag; empty when full to maintain airflow.

Tip: Never cut more than 1/3 of grass height at once. Sharpen blade annually.

Maintenance Schedule

Regular maintenance ensures longevity and performance.

IntervalTask
Before each useCheck oil level, inspect blade, clear deck of debris
Every 25 hoursChange engine oil, check air filter, inspect spark plug
Every seasonSharpen or replace blade, clean underside of deck
As neededReplace air filter, fuel filter, spark plug

Oil Change: Run engine briefly to warm oil, drain via dipstick tube or drain plug. Refill with SAE 30.

Storage & Winterization

Prepare mower for off-season storage.

  1. Drain fuel: Run engine until tank is empty, or add fuel stabilizer.
  2. Change oil: Replace with fresh oil to prevent corrosion.
  3. Remove spark plug: Add 1 teaspoon of oil into cylinder, pull starter slowly to coat, reinstall plug.
  4. Clean deck: Scrape off grass and debris; apply light oil to prevent rust.
  5. Store indoors: Keep in dry, covered area; cover mower.

CAUTION! Never store with fuel in tank for more than 30 days without stabilizer.

Safety Information

Read all instructions before operating. Always wear sturdy shoes and eye protection.

WARNING! Gasoline is flammable; store in approved container away from heat sources.

Warranty & Support

Murray 225114X92E2 is covered by a 2-year limited warranty for residential use. Warranty does not cover commercial use, neglect, or improper maintenance. For support, contact Murray Customer Service at 1-800-800-7310 or visit www.murray.com. Have model and serial numbers ready (located on deck near rear wheel).

Troubleshooting

SymptomPossible CauseCorrective Action
Engine won't startNo fuel, old gas, clogged filterAdd fresh fuel; check fuel line; clean/replace air filter.
Engine runs poorlyDirty air filter, old oilClean air filter; change oil; check spark plug.
Uneven cuttingDull blade, uneven heightSharpen or replace blade; adjust all wheels to same height.
Excessive vibrationLoose or damaged bladeStop engine, check blade tightness and balance; replace if bent.
Grass not dischargingWet grass, clogged deckMow when dry; stop engine and clear deck underside.

Reset: For engine safety switch issues, ensure blade control bail is fully engaged.

Service: 1-800-800-7310; www.murray.com

Murray 225114X92E2 Lawn Mower Manual © - All Rights Reserved 2025