Murray 20606X9A Lawn Mower Manual

The Murray 20606X9A is a 20-inch push lawn mower featuring a Briggs & Stratton 125cc engine, 3-in-1 mulching/bagging/side-discharge capability, single-lever height adjustment (6 positions: 1.5-3.75 inches), durable steel deck, easy-fold handle, and washout port for cleaning. Below are key sections for safety, features, assembly, operation, maintenance, and troubleshooting.

1. Features at a Glance 2. Assembly Instructions 3. First-Time Setup 4. Specifications 5. Controls and Operation 6. Cutting Height Adjustment 7. Mulching & Bagging 8. Safety Features 9. Maintenance & Storage 10. Warranty Information 11. Troubleshooting

Features at a Glance

Key components: Briggs & Stratton engine, steel cutting deck, foldable handle, rear bagger, washout port, single-lever height adjuster.

Feature	Description
Engine	Briggs & Stratton 125cc, 450E series, recoil start
Cutting Width	20 inches
Cutting Height	6 positions (1.5" - 3.75")
Deck Material	Durable steel with corrosion-resistant finish
3-in-1 Function	Mulch, bag, or side discharge
Handle	Easy-fold design for compact storage
Washout Port	For easy deck cleaning after use
Wheels	8-inch rear, 7-inch front
Fuel Tank	0.95 quart capacity
Oil Type	SAE 30 (10W-30 acceptable)

Assembly Instructions

Unpack and inspect all parts. Assembly requires basic tools (included).

Attach handle: Insert lower handle into deck brackets, secure with provided bolts and wing nuts.
Install upper handle: Connect to lower handle, secure with knobs.
Attach grass bag: Hook bag frame onto rear deck brackets, ensure secure fit.
Install side discharge chute (if not mulching): Attach to deck opening.
Add engine oil: Fill to proper level on dipstick (check manual for capacity).
Add gasoline: Use fresh unleaded gasoline (87 octane or higher).

WARNING! Do not add gasoline during assembly or near open flames. Ensure all fasteners are tight.

First-Time Setup

Before first use, complete final checks and safety inspection.

Check oil level: Ensure oil is at full mark on dipstick.
Inspect blade: Ensure blade is properly installed and sharp.
Test height adjustment: Move lever through all positions to ensure smooth operation.
Test engine start: Follow starting procedure in open, well-ventilated area.
Engage safety features: Verify blade control lever must be held to keep blade engaged.

CAUTION! Always wear sturdy shoes and eye protection during operation. Clear mowing area of debris.

Specifications

Model: Murray 20606X9A
Engine: Briggs & Stratton 125cc, 450E series
Cutting Width: 20 inches
Cutting Height Range: 1.5 - 3.75 inches (6 positions)
Deck: 20-inch steel, 3-in-1 capability
Wheels: 8-inch rear, 7-inch front
Fuel Capacity: 0.95 quart
Oil Capacity: 20 oz (0.6 liter)
Weight: Approximately 65 lbs
Warranty: 2-year limited

Controls and Operation

Key controls: Blade control lever, drive control bar (if self-propelled model), height adjustment lever, throttle control, primer bulb, recoil starter.

Starting Procedure:

Check oil and fuel levels.
Move throttle control to FAST position.
Press primer bulb 3 times (cold engine).
Hold blade control lever against handle.
Pull recoil starter briskly.

Stopping: Release blade control lever; move throttle to STOP. Wait for blade to completely stop.

Cutting Height Adjustment

Single-lever adjustment for all four wheels simultaneously.

Stop engine and wait for blade to stop.
Pull height adjustment lever toward wheel.
Move lever to desired position (1-6, with 1 being lowest).
Release lever to lock in position.
Test by gently rocking mower to ensure all wheels are at same height.

Tip: For first mow of season, set to highest position, then gradually lower.

Mulching & Bagging

3-in-1 system: Install appropriate accessory for desired function.

Mulching: Install mulch plug (closes side discharge). Grass is cut finely and returned to lawn as fertilizer.
Bagging: Attach grass bag to rear. Empty when bag is 2/3 full for optimal performance.
Side Discharge: Install discharge chute. Use for tall or wet grass.

WARNING! Always stop engine before changing cutting mode. Ensure all attachments are securely installed.

Safety Features

Blade control safety lever: Blade stops within 3 seconds of release. Safety labels: Read and understand all labels on mower. Protective shielding: Keeps debris contained. Washout port: Allows cleaning without tilting mower.

Maintenance & Storage

Regular maintenance ensures optimal performance and longevity.

After each use: Clean underside of deck using washout port. Check blade for damage.

Monthly: Check air filter, clean or replace if dirty. Check blade sharpness.

Seasonal: Change oil (first 5 hours, then every season). Replace spark plug annually. Sharpen or replace blade as needed.

Storage: Drain fuel or add fuel stabilizer. Store in dry, covered area.

CAUTION! Disconnect spark plug wire before performing any maintenance. Never store with fuel in tank near open flame.

Warranty Information

Murray 20606X9A includes a 2-year limited warranty covering defects in materials and workmanship. Warranty does not cover normal wear, misuse, or lack of maintenance. For warranty service, contact Murray customer service at 1-800-800-7310 or visit www.murray.com. Keep original receipt as proof of purchase.

Troubleshooting

Symptom	Possible Cause	Corrective Action
Engine won't start	No fuel, old gas, clogged filter	Check fuel level; use fresh gas; clean/replace air filter; check spark plug.
Engine runs poorly	Dirty air filter, old gasoline	Clean air filter; drain and replace with fresh gasoline.
Uneven cutting	Dull blade, uneven height	Sharpen or replace blade; check height adjustment on all wheels.
Vibration	Loose blade, bent blade	Stop engine, disconnect spark plug, tighten blade bolt or replace blade.
Bag not filling	Wet grass, clogged deck	Mow when grass is dry; clean underside of deck.
Wheels not turning	Debris in wheel gears	Clean wheel axles and gears; lubricate if necessary.

Service: For repairs beyond basic maintenance, contact authorized service center at 1-800-800-7310.